
The time has come. We’ve been putting out memes all year, and the best of the best have shown up to see who will come out on top. Here is the 4th Annual Audio Hertz Super Duper Really Great Audio Engineer and Music Producer Meme Awards.
The time has come. We’ve been putting out memes all year, and the best of the best have shown up to see who will come out on top. Here is the 4th Annual Audio Hertz Super Duper Really Great Audio Engineer and Music Producer Meme Awards.
Well, it’s the end of the year, and it’s time to reevaluate the important things in our lives, like the most liked memes from Audio Hertz. Dozens, maybe even two dozen audio comedy fans, have been eagerly anticipating which meme would come out on top– I’ve had to personally stop a few fights before they got out of control. Anyway, here is the 3rd Annual Audio Hertz Super Duper Really Great Audio Engineer and Music Producer Meme Awards.
Audio oscillators are most commonly used in music production as tone generators and measurement tools. Technically, an oscillator circuit converts DC to AC current, which produces a continuous, repeated, alternating waveform. They are most commonly used to produce waveforms in the desired frequency, ranging between 16 Hz to 20,000 Hz. A low-frequency oscillator, or LFO, generates waveforms below 20 Hz. The electrical current alternates very quickly between two states, much like a string resonates on a guitar; this produces a waveform that can be amplified and shaped with various other audio processors. Additionally, electronic oscillators are widely used in many industries as equipment clocking, measurement, and calibration tools.
The most common types of oscillators found in analog synthesizers are voltage-controlled. A voltage-controlled oscillator, or VCO, is an oscillator in which the frequency depends on a control voltage. These oscillators will produce a different frequency depending on the control voltage it is being fed. When a key on an analog synth is pressed, it sends a specific voltage to the oscillator, which generates a waveform in the corresponding pitch. If the oscillator is tuned properly, the pitch will correspond with the note of the key that is pressed. Additionally, synthesizers will usually offer the ability to modulate the control voltage with different types of signals. For instance, adding modulation to a VCO can produce Frequency Modulation, better known as FM synthesis.
Voltage-controlled oscillators have three main parameters– frequency or pitch, amplitude or volume, and waveform or tone. A sine wave is the most basic of all waveforms; additional harmonics are added to alter its shape. The four main waveform shapes are sine, square, triangle, and sawtooth. Each type has a major impact on the tonality of the sound produced. Sine waves are usually classified as having a smooth sound, while a sawtooth is more harsh or buzzy. Another common waveform seen on oscillators is noise which most commonly comes in the white and pink variety. White noise contains all frequencies in equal proportions, while pink noise attenuates some of the higher frequencies.
Digital oscillators generate waveforms using digital signal processing or DSP. The waveforms are modeled and digitally recreated to emulate analog oscillators. Although modeling technology continues to get better and software manufacturers are making better sounding applications, most synth enthusiasts consider digital oscillators’ sound to be inferior to analog. However, the flexibility of digital gives manufacturers new opportunities to expand sonic possibilities.
Oscillators can produce a wide range of shapes, but the four most commonly found on an analog synthesizer are a Sine, Square, Triangle, and Sawtooth. The curve of the waveform line is what dictates its shape.
A sine wave is arguably the most fundamental building block of sound. It is considered pure because there are no additional harmonics added to the signal; it is only made up of the fundamental frequency.
In addition to the fundamental frequency, a Square Wave only includes odd harmonics or harmonics that occur in whole odd-number multiples of the fundamental frequency. A square wave looks like its namesake, a square.
Triangle waves look similar to a sine wave, except the curves are replaced with straight edges that connect like a triangle. Triangle waves add in odd harmonics, which diminish the further away they get from the root frequency. For example, the root note and the 3rd harmonic will be the loudest, while the 5th and 7th harmonic will be lower in level and the 11th and 13th even lower.
The Sawtooth is named after its resemblance to a sawtooth blade. In these waves, both even and odd harmonics are added, resulting in a harsh but clear tone.
In the late 1930s, audio oscillators were less than ideal for modern applications due to their complexity, instability, and cost. This prompted William Hewlett to develop his first product for the Hewlett Packard company, the model 200B variable frequency oscillator. Hewlett was inspired after seeing a seminar at Stanford University during the late 1930s by his professor Frederick E. Terman on the use of negative feedback. He was so intrigued he decided to spend an entire semester studying it for his thesis needed to complete his advanced engineering degree.
The main difference in Hewlett’s oscillator is the incandescent lamp that is used as the temperature-dependent resistor in the feedback network. The light bulb also acted as an automatic gain control that kept the oscillator’s loop gain near unity, which is a key component to achieving the lowest amount of distortion. With this design, the output could be regulated without adding distortion. This not only improved the performance but also made it much more affordable. The Model 200A at the time sold for $54.40, which was substantially less than most of the other oscillators on the market, going for anywhere between $200-600. The first big sale which launched the entire company was to Walt Disney, whose engineers used them to test channels, recording equipment, speaker systems, and other equipment needed for its new Fantasound stereo sound reproduction system that was used for their breakthrough classic Fantasia. Fantasia was the first film that was commercially released in stereo.
Hewlett’s oscillator was the first practical method for generating audio signals, used for measurement and calibration in communications, science, medicine, audio, and many more industries. Before Hewlett’s 200B, there was no easy and accurate way to produce low-frequency signals.
The end of the year list you’ve all been waiting for is finally here. Forget Best Albums, Greatest Moments, or Best Selling lists– this is the only one that really matters. And now, the moment you’ve all been waiting for… Welcome to The 2nd Annual Audio Hertz Super Duper Really Great Audio Engineer and Music Producer Meme Awards.
Disclosure: Audio Hertz is supported by its audience. When you purchase through links on our site, we may earn an affiliate commission.
Like it or not, the holidays are upon us again. Where did the time go? Oh yeah, I remember; they were spent locked in my apartment, gripped with fear and crippling anxiety. Well, hopefully, the holiday season will be the start of something new and better. For one thing, we know we are close to the end of the year, and it couldn’t come any sooner. Regardless of how you’ll be spending the holiday season, it’s always a good idea to show the people you love that you’re thinking of them.
Is one of your loved ones a music producer? Do you need to buy them a gift? There’s good news! I’ve put together a comprehensive guide that will take all of the thinking out of it. Everything on this list is guaranteed to make any recording musician, audio engineer, or music producer excited. You can’t miss!
I’m sure if you were to ask most people what the best gift was, it would never be something that the recipient has to spend time building… but these wooden diffusers are extremely easy to put together as there are included instructions, and everything comes pre-cut. If you want to be an even better gift-giver, you can build it for them! Diffusers of this quality will typically go for up to 3-4 times the cost of just one of these kits.
Studios can get messy! Anything that will help me organize my space, so I don’t have to worry about cleaning up as often is something I’m extremely interested in. I found this nifty cable hanger randomly and thought it was a great way to easily store cables. I currently go with some cheap cup hooks, but this design is pretty genius and makes a great gift for any musician. We all have a ton of cables lying around our room. It’s part of the job.
Recording studios have cables. Lots and lots of cables. It’s more difficult than it should be to store them easily. This wall-mountable cable hanger solves that age-old problem by making it easy to hang and retrieve your most used cables of all sizes.
There’s no replacement for treating a room properly, but these portable reflection filters definitely help and are great to have around any studio. These things make it easy to set up and record quality sounding vocal tracks anywhere you want. With a good reflection filter, you can be confident that your tracks will definitely be useable when it comes time for mixing. I also like these when I record vocals without headphones, as they do a great job of blocking out the sound from the speakers. They are well worth it for the price, and any producer with a home studio would benefit and appreciate having one of these around.
Scott Iulianelli has been making some absolutely killer analog inspired art merch for the last few years. His work never ceases to amaze me, and I would buy it all if I could. You can’t go wrong with anything in his store.
This classy, sleek synth poster would look great on the wall of any studio or music room.
You really only see them in old movies and television shows, but I’ve always wanted one of these to hang in my room. This is the perfect accent for any home studio, and it’s something most wouldn’t buy for themselves, which makes it a great gift.
A musician’s solution to the classic dilemma that is misplacing your keys. These are handmade in the good ol’ USA and include 1/4″ plug keychains. Plug in your keys when you get home and unplug them when you’re ready to head out. The cherry on top is that the jewel light really works when you turn it on.
You can never have enough hard drives. Give the gift of more storage space this year. The Samsung T5 and the WD My Passport are solid-state or SSDs. Solid-state drives are more reliable and have much faster read and write speeds than your standard hard drives. These are best used as work drives to save projects and sample libraries. The 5TB WD Elements is a standard hard drive, which, although it has slower read and write speeds, is more affordable and a better option for long term storage.
This is one I included on my list last year, and it will probably be on my gift guide every year for the rest of entirety. If you couldn’t tell from my emphasis on hard drives, backing up files is important for all audio engineers and producers. Unlike painters that have to store large canvas, as musicians, our art lives in the digital realm, and services like Backblaze make it easy to preserve our most valuable creations.
$5 a month for unlimited cloud storage! $5 lets you back up as many files as they can throw at it. The desktop application allows you to seamlessly back up your drives as well as set up an upload schedule. Whoever gets this will never lose another session again!
Shortcuts or hotkeys are a combination of keys on a keyboard that perform a task on a computer or, more specifically for musicians, a digital audio workstation. Using hotkeys speeds up workflow drastically. Someone that is well versed in the hotkeys of their DAW of choice looks like a magician while they are mixing or editing, easily jumping from different tasks where it might take two or three times as long if they had used the mouse to do the same task. The only hard part about hotkeys is remembering them. It’s like learning another language. These keyboard covers put the hotkeys right in front of you. Not only is it a convenient reference tool, but it also teaches you hotkeys you might not have known before. If you’re buying this for someone, make sure you know what DAW they use and what type of computer they have.
The Stream Deck is the future! Originally developed for streamers and content creators, the Stream Deck can be utilized to map tasks in applications to buttons. You can make your own shortcuts in your DAW of choice and map them to the 16 configurable LCD buttons. You can even put custom graphics or text on each of the buttons. The possibilities are endless with this thing. You have to see it to believe it. Check out this demonstration video below.
Cases and dust covers. We hate to buy them, but we all need them, which means they make a great gift.
David Byrne is a musical Yoda. In his book “How Music Works,” Bryne elegantly explains how music is shaped by our surroundings. He also gets into the beginning of recording technology and the profound impact it has had on the world we live in. If you’re looking to open up a musician’s mind and have them look at their art form in a new exciting way, this book is the perfect gift.
My favorite book on mixing. It’s one of the only books I will go back to over and over again. Even after reading it multiple times, I’ll still pick up something new. Books make great gifts, and this is one every mixing engineer should keep on their shelf.
This might be the most valuable resource for any recording musician, music producer, or audio engineer. These well-made tutorial videos allow you to work right alongside some of the greatest minds in the industry.
Everyone needs a Leatherman. And by everyone, I mean every single person that exists in the world. Receiving your first Leatherman is a right of passage that all audio engineers need to experience. Trust me, it’s an incredibly rewarding experience; imagine walking around with a single tool that could do as much as 13 individual tools. Can you imagine the power you would wield? No, you didn’t just become Superman; you’re only holding a Leatherman. You can even store it in the included sheath and attach it to your belt, like it’s Excalibur.
This guitar multi-tool has everything you need to adjust guitars. Great for having around the studio in case any guitars need some fine-tuning.
Stringing a guitar is annoying. This tool makes it less annoying.
This spray can be found in just about every studio around the world. A little spritz of this stuff helps protect, lubricate, and improve the conductivity of electronics. It also helps reduce intermittent connections, arcing, and RFI, as well as wear and abrasion. Not the sexiest gift but definitely something useful that anyone with a lot of gear could use.
This cool little gadget tells you if your AC adapters are working properly. Simply plug in a synth or guitar pedal power adapter to the hot tip, and it will light up if it is receiving the correct amount of power to the device. If you have a lot of AC adapters, you know that they don’t always last forever, the hot tip allows you to quickly check if an adapter is working properly.
This guitar effects router allows you to use any guitar pedal as a piece of outboard gear. That means with this little orange guy, it’s possible to send anything you want out of your DAW to your favorite delay, distortion, or any other guitar pedal you may have lying around. Start putting those pedals to use on more than just a guitar!
This 500 series module lets you use the reverb tank on a guitar amp as a piece of outboard gear. Use the Tank Driver to send anything to a guitar amps reverb tank, and record it back into a DAW for a truly authentic-sounding spring reverb. Pretty nifty.
This badass palm-sized, battery-operated synth is a real workhorse. The synth is made up of a ribbon keyboard controller, 5 knobs, and a single switch. The simplicity makes it easy to get started, but the unit’s more advanced capabilities are truly remarkable. The included delay and original MS-20 filter put it over the top. I also love that it has an aux input, so you can use the filter on any source external source. It’s an incredible value and insanely fun little go-anywhere synth.
This little battery-operated amp sounds better than you probably think. Connect the amPlug to the input of your guitar and use the headphone output to hear that sweet vox tone. With this thing, practicing at night will no longer be a problem.
The Jammy G might have the worst name ever, but it is a great idea and extremely well done. This digital midi guitar can be used to control any software instrument or device in a DAW. The guitar has 15 frets with sensors that track finger position, string muting, and bends. The built-in USB port allows you to connect it to ur computer easily. But the best part about this thing is that it has nearly zero latency, which makes playing it much more seamless.
It’s definitely not a replacement for a guitar as the feel of the sensors takes getting used to, but once you do, it’s hours of fun and a legitimate production tool. It’s a new world being able to play my synths and software instruments like a guitar. As a composition tool, the Jammy G gives me a fresh approach to writing chord progressions and melodies. I’ll often find myself creating things I wouldn’t have been able to if I was using a standard keyboard or using my mouse to click in notes on the piano roll.
This 4-track portable recorder makes it easy to record anywhere on the go. Capture any sound you want quickly and easily. The built-in Stereo X/Y condenser microphones sound remarkably good, and there are also analog XLR/TRS mic and line inputs.
Everyone needs two of each of these. The Shure SM57 and 58 dynamic microphones are staples of recording. Every recording musician would be happy to have more of them! The Sony 7506s are the classic closed-back over-ear headphones with a pronounced mid-range. They can be found in just about every recording and broadcast studio around the world. The Radial Pro DI is a little green box that does its job and does it well, whether you’re using it to DI a bass guitar or a synth; there’s nothing I wouldn’t feel comfortable putting through this bad boy.
Disclosure: Audio Hertz is supported by its audience. When you purchase through links on our site, we may earn an affiliate commission.
Whether or not you’re a fan of the Beatles, if you’re into audio or music production, you need to appreciate the groundbreaking recording and production techniques used at Abbey Road. Geoff Emerick is the audio engineer who was behind the console while the Beatles were recording many of their most famous tracks. His memoir gives a first-hand account of what it was like to work with the four mop tops in the heyday of their popularity. His life story is fascinating, having begun working at EMI studios when he was just 15. By 19, he was tasked with recording the biggest band in the world, eventually becoming one of the most influential audio engineers of all time.
Ken Scott was another one of five people that had the privilege of standing behind the desk for the Beatles. He also was responsible for engineering David Bowie’s famous Ziggy Stardust and has worked with artists like Pink Floyd, Jeff Beck, Elton John, Supertramp, The Rolling Stones, Harry Nilson, Kansas, Lou Reed, America, and many more. Like Emerick, Scott rose to prominence as a staff engineer at Abbey Road. He was displeased with Emerick’s portrayal of The Beatles and their producer George Martin which led to him refuting some of his stories in this book.
Glyn Johns was one of if not the most sought after audio engineers in London during the 1960s. Johns specialized in working with the original artists and finding a sonic character that complemented their music. He was also a pioneer in creating new techniques and, most notably, for his drum mic technique, which many engineers still use today. This book is as close as it gets to being a fly on the wall in some of the most famous and monumental recording sessions there ever were.
Phil Brown might not be as well known as some of the others on this list. Still, his story is not any less impressive. Brown started his career as a junior technician in 1967 and learned by working under such audio geniuses as Glyn Johns and Eddie Kramer. Eventually, he was recording some of the most prominent artists, such as Mott the Hoople, Bob Marley, David Bowie, Talk Talk, Steve Winwood, Dido, and Robert Plant. The book covers much of Brown’s time spent in the studio, including techniques and gear that he used. The reader is also given an intimate look into an audio engineer’s life during this time period. Brown talks very candidly about his struggles with balancing his home life, drug abuse, and dealing with the industry’s challenging social and political aspects.
Al Schmitt is a living legend in every sense of the word. A true master of the craft that is respected by every single person in the industry. His incredible story begins in New York City as a young kid visiting and eventually working at his Uncle Harry’s studio. He went on to apprentice under the godfather of audio engineering, Tom Dowd. His first real session was with Bing Crosby when he serendipitously was the only engineer available to run the session. You can only imagine everything else this man has seen and been a part of– He has worked with Frank Sinatra, Ray Charles, Sam Cooke, Bob Dylan, Elvis Presley, Madonna, and Paul McCartney, to name a few. Schmitt has engineered over 150 albums and has over 20 Grammy awards, more than any other engineer or producer. He was also the first person to win both the Grammy and Latin Grammy for Album of the Year.
Phil Ramone has worked with everyone. Ray Charles, John Coltrane, Bob Dylan, Elton John, Billy Joel, Paull McCartney, Frank Sinatra, Paul Simon, and Stevie Wonder. He established one of the earliest independent recording studios, A & R Recording, with Chief Engineer Bill Schwartau in 1959. He was sought after for his impeccable sounding records and innovative use of technology. Ramone has been nominated for 34 Grammys and won 14 of those, including a Technical Grammy for a lifetime of innovative contributions to the recording industry, Best Engineered Recording. He’s produced the Album of the Year, the Record of the Year, and in 1981 won Producer of the Year. In his later years, he transitioned into an executive role for The Recording Academy.
Ken Calliet was the man behind the glass and turning the knobs when recording some of the most significant songs ever produced. Fleetwood Mac’s Rumors sold over 45 million copies and went 20 times platinum. Making Rumours gives you an insider look at what it was like to work in Los Angeles with the Mac in 1976. On top of the musical significance, there was no shortage of drama, as sex and drugs were aplenty. There was also some drama stemming from multiple romantic relationships between band members ending shortly before the recording of the album started. Calliet tells his side of the story and gets into the more technical information about the recording and mixing process. If you’re a fan of this album (and you’d be crazy not to be), you’ll enjoy the read.
Learn about how a young kid from Brooklyn moved to the UK and became a pivotal part of launching an entire genre known as Glam Rock. Visconti was one of the most influential music producers of the 1970s. Most famously known as the producer behind David Bowie’s records, he has also worked with other famous artists such as T. Rex, Moody Blues, Joe Cocker, Thin Lizzy, Morrisey, Paul McCartney and Wings, and many more. Visconti’s nonjudgemental, honest and straightforward storytelling makes this one of the most readable memoirs on this list.
If you’re not familiar with Rudy Perez’s name, you’ve, without a doubt, heard some of his music. Perz has produced over 70 albums and written over 1000 songs, of which over 300 have reached the top 10 charts. He has worked with world renowned Latin artists such as Julio Iglesias, Marc Anthony, and Luis Fonsi and mainstream artists such as Christina Aguilera, Michael Bolton, Beyonce, Jennifer Lopez, and many more. His music accolades aside, he has a fascinating and true rags to riches story. He was born in Cuba and fled the country to escape the political regime. His family eventually made it to Miami, where they were forced to live in a refugee camp before they were able to settle in Florida. He quit school at 15 and worked his way up to working with some of the most prominent artists of all time. This is one that you’re guaranteed to enjoy, and it will be difficult to put down.
Ted Templeman, who is most famously known for working with Van Halen, The Doobie Brothers, and Aerosmith, was a hitmaker for Warner Brothers in the late 1970s and 1980s. Templeman generated worldwide sales approaching 100 million albums. Templeman’s story has an appropriate amount of sex, drugs, and of course, rock and roll; he’s also able to sprinkle in plenty of the technical information of the recording process.
Disclosure: Audio Hertz is supported by its audience. When you purchase through links on our site, we may earn an affiliate commission.
You’ve probably seen plugins, guitar amps, or stereos that replicate a Baxandall circuit, or maybe you’ve heard of the popular Dangerous BAX mastering equalizer. Peter Baxandall designed the Baxandall tone circuit or EQ in 1950, and they were then implemented into millions of audio systems around the world.
The Baxandall equalizer is a shelving EQ, but unlike traditional shelving EQs, which have a steep rise or fall above the set frequency, the Baxandall shelving curve has an extremely wide Q curve, which creates a gentle slope. The broad curve can adjust a large portion of the frequency spectrum, but the gentle slope allows for a more natural sound and minimal phase distortion. The minimal phase distortion enables users to make more drastic boosts and cuts without imparting negative artifacts into the signal. This results in a wide, open sound that enhances the source’s sonic character that’s already there rather than imparting its own sonic character. These equalizers offer a subtle yet remarkably effective way of adjusting the frequency spectrum, which is why you’ll often find them being used on the mix bus and for mastering.
During World War II, Baxandall consulted for the Telecommunications Research Establishment in the Circuit Research Division. It was there he spent his time working on many different types of projects, including frequency transformers, powered loudspeakers, oscillators, high-speed tape duplicating equipment, and high precision microphone calibration methods, among many more things. His hero, Alan Blumlein, who you might know for his stereo micing technique, also worked for the TRE.
Lucky for us, Baxandall was enormously generous and patient with passing on his knowledge. He was also remarkably good at conveying very complicated topics in a simple and easily understandable form. He published his tone circuit in a 1952 article in Wireless World magazine. Have you ever seen the Bass and Treble knobs on a stereo? That’s likely a Baxandall EQ circuit. He never collected a single royalty, while even a minuscule percentage would’ve made him an extremely wealthy man. This might be the greatest testament to his generosity; he genuinely wanted the world to sound better.
The term equalization was likely derived from the various operators’ requirements at the time (phone, motion picture, broadcast, etc.) that were attempting to get their audio back to a flat frequency response or equal. Equalization, or filtering as it was also called, has been part of audio equipment since the beginning of the technology. Early radios came equipped with high frequency or top cut filters to remove unwanted noise or artifacts. Early telephone lines used equalizers to put back the high end that was lost in transmission. These equalizers were not fully adjustable like the parametric equalizers you’ll find in your DAW today.
These plugins are available for free,
Acustica Audio Coral Bax-ter EQ
Kuassa BasiQ
Fuse Audio Labs RS-W2395C Baxandall EQ
Accumulating plugins is addicting, and if you’re not careful, it can get expensive. Luckily there are a lot of great software developers offering their plugins to the music production community for free. Here are a few incredible sounding compressor plugins that, if they weren’t free, I would gladly pay for.
All of these plugins are 100% free and available in VST, VST3, AU, and AAX formats.
Link to the developers Patreon,
https://www.patreon.com/analogobsession
Disclosure: Audio Hertz is supported by its audience. When you purchase through links on our site, we may earn an affiliate commission.
It’s a lot harder to procrastinate your to-do list when it’s staring you in the face every day. When you wake up, there it is; when you change your clothes, there it is; when you go to sleep, there it is. These boards make it easy to write out lists or draw things to help plan projects or visualize techniques or concepts. Sometimes words are confusing, and it’s easier to draw a picture. Dry erase markers make it easy to add and change things as you go, and the scented ones smell good. I like to use whiteboards to track the progress of projects. It usually will take multiple sessions to complete projects. Adding a list of things I’ve done and things I still need to do makes it easy to stay productive and complete tasks.
No cable shall be left untied! That is the vow I make every single day I step foot into the studio. It is my duty as a qualified, experienced audio engineer to wrap my cables properly and make sure they are tied!
But seriously, make sure your cables are tied! Velcro cable ties help you organize and manage cables, which makes things look cleaner. Managing your cable clutter keeps your studio looking a little less messy. I’m not a massive fan of having an immaculate studio, but I emphasize cable management, as I’m a firm believer that a poorly run cable is an unhappy cable. Look up ways to neatly organize and manage your cables in your studio so you don’t have to look at a big rat’s nest on the ground all the time; you’ll thank me later.
Wrap your cables and velcro them together for optimal storage and transportation. No more tangled wires!
You get a label! And you get a label! Everything gets a label! I’m the Oprah Winfrey of labeling things. I love knowing exactly what is in a box when I look at it. You’d be surprised how much time it saves when you’re looking at something and can tell what it is right away. Labeling can save seconds or even minutes, and those can add up. I also like to label any switches or buttons. For instance, I have a passive speaker switcher from Coleman Audio, so I label each button with the corresponding speaker. Now anyone that comes into my studio knows what button engages which pair of speakers. Labeling everything is especially necessary if other engineers or producers are going to be using your studio.
Another beneficial way of using the label maker is to label the ends of cables. Labeling both ends allows you to know where each cable goes quickly, regardless of which side you look at. This is extremely useful when making long runs, where it can get confusing fast.
You might think this looks like regular old masking tape but go and try and use masking tape to label your gear. Good labeling tape is thick enough to write on with a sharpie and isn’t completely translucent; it also doesn’t leave a residue when you take it off.
I use labeling tape for obvious uses, such as temporarily labeling a mixing console, switches, cables, and other gear. I also use it to write passive-aggressive notes around the studio, such as “HANDS OFF” or “DID YOU PUT IT BACK WHERE YOU FOUND IT?”
I don’t know what I did before I found gaffer tape. If you’ve worked in Live Sound, Theatre or Film, you’re likely already familiar with the magic that is gaffer tape. I literally will use the stuff for everything. If anything needs holding in place, I grab the gaff tape. Gaff tape is like duct tape, except it’s way better. The main difference is gaff tape is made with cloth instead of vinyl, and the adhesive comes off easier and leaves little to no residue. One of the most common uses of gaff tape is to adhere cables to the floor so they’re not tripping hazards. I recently had some blinds on my bedroom window that didn’t want to close all the way– a little gaffer tape and that problem was solved quickly and easily, albeit maybe not the most attractive.
Because you can never have enough sharpies! Sure, you can label things with your new label maker, but you’ll also need to mark things on the fly that are temporary. After applying artist tape to the console, I use sharpies to label each channel. I also use Sharpies to label the end of cables. You can see I like to label things. Labeling helps you stay organized, and being organized saves you time and helps you work more efficiently.
Control rooms and recording studios can get weird. You never know when you might have twelve percussion instruments, a vintage tape delay, and three laptops that you need to put somewhere. Foldable tables and chairs of all sizes are lifesavers when it comes to times like these. It also prevents accidents when someone decides to put something expensive on a window ledge, and it falls as soon as the drummer hits the kick drum.
Because everyone needs light! I like to keep my studio somewhat dark and vibey, and clip-on lights allow me to easily grant my clients the ability to illuminate whatever they want at the drop of a hat. Throw one on a music stand, desk, pedalboard, amp, or synth. Whatever needs illuminating, one of these babies has got you covered!
We’ve all been there– you have two pieces of gear that need power and only one outlet. Do you play the ol’ ‘let me unplug the one I don’t use as often now, and then when I need it, I’ll figure it out’ game? Just kick the problem down the road to the future you? No! No, you don’t!
With one of these 1 to 4 outlet power splitters, you can turn a single outlet into 4. It also helps when you have a couple of fat wall warts (fat wall wart shaming is allowed) that need extra space that your surge protector, power conditioner, or UPS doesn’t have. They also make these 1 to 2 or 1 to 1. I like to have a few of these lying around, so I never have to worry about fat wall warts spoiling the party.
Turn anything on or off from your smartphone using an app. You can control these devices when you’re not at home or put them on a schedule or timer.
I’ve found a lot of uses for these. I have one connected to a fan in the live room, and now when someone forgets to turn it off, I can do it from my phone. Instead of asking one of my clients or an intern to go into the live room to turn it off before we start recording, I can open an app on my phone and tap a button. It’s incredibly convenient, and I’ve found other one-off uses for these as well that have made them a handy tool to have around the studio.
I don’t think many people know this, but indoor security cameras are incredibly cheap and work pretty damn well. If you have people at your studio, especially if your studio is in your house, it’s not a bad idea to get a few of these so you can monitor what’s going on remotely. This one even has a motion detector, so you can set to start recording when it detects movement, and it will then immediately upload it to a cloud storage service. I’ve been fortunate that I haven’t dealt with many thieves or dishonest clients. Still, it’s always good to plan for the worst, and a camera is an excellent way to ensure your studio and possessions’ safety if anything does happen.
Maybe it’s the cable? I’ve probably heard that a million times in my career. Spoiler alert! It’s usually not the cable, but at least a cable tester will give you a quick and easy way to find out if it is. These are also especially vital if you make your own cables and check to ensure everything is wired correctly. I’ve wired a few XLR cables backward in my day. The cool part about this tester is it does 12 different types of connections commonly found around a recording studio. This device can test for other types of connections: USB, RCA, Speakon, Banana plugs, DIN, RJ45, and more.
Microphones can be heavy. I like to have sandbags around to help weigh down any stands that may seem a little less stable than I’d like. A few sandbags on the bottom of a stand will help ensure your stands stay where you want them, so you don’t go slamming the original Neumann U47 on the floor of your studio.
Backup your files, back up those files, and then back up those files. I used to be really careless when it came to storing old projects and files. It turns out those files meant a lot to me and having them in just one place wasn’t a good idea. There is nothing worse than losing a project or session. You’ll never get it back.
It would be best if you always had everything important backed up at least three times, with one of those backups being in a different location than the other two. If any of your data is only in one place, you’re at risk of losing it. It’s essential to have not only local backups of your files but also off-site or cloud backups. If there is ever a fire or natural disaster and the location where your drives are stored is damaged, you won’t be able to retrieve your files, no matter how many copies you have. This is why having a cloud storage service like Backblaze is so crucial if you’re serious about keeping your data forever.
Backblaze is a cloud backup service that automatically backups every one of your drives for only $5 a month. If you ever lose a hard drive or a file, you can download it or have them send you a hard drive with the same files on it. I’ve lost some of my old music that I wish I still had. I will never make that mistake again. With Backblaze, I’m guaranteed to have my files no matter what happens.
If you’re not familiar with Valhalla DSP plugins, then you either just started recording yesterday, or you live under a rock. For the last 13 years, founder and head reverb and delay algorithm mastermind Sean Costello has been putting out some of the best sounding and most widely used plugins available. From the massive list of famous musicians and producers that are believers of his reverbical prowess to the fact that you’ll find all of his plugins in just about every recording studio around the world, it’s obvious he makes some of the best-sounding plugins out there.
On the Valhalla DSP website, Costello talks about his obsession with digital signal processing algorithms and his immense passion and desire to produce immaculate sounding reverbs. His passion, combined with a background consisting of over ten years of experience, are the ingredients that allow him to create some of the best and most highly regarded reverb and delays.
If you mention the name Valhalla to producers, you’ll almost always be met with a resounding nod of approval, usually accompanied by a few kind words delivered in an excited tone. Not only are they practical, intuitive, and easy to use, but they are also incredibly affordable– all of their paid plugins are just $50. If you can’t afford something regardless of how fairly it’s priced– Valhalla DSP is generous enough to offer a few plugins for free to anyone that knows how to click a link on a website. That’s right; not only is Valhalla giving it away for free, but they aren’t asking for anything in return, not even an email address or a follow on social media. It is a truly admirable way of marketing and an incredible asset to producers and audio engineers.
Valhalla’s second free plugin, Supermassive, takes reality and throws it on its head. Costello thought it was silly to only focus on realistic sounding algorithms. Before Supermassive, his primary goal was to preserve the natural characteristics of reverb you’d find in real environments. Realistic reverbs are familiar to our ears, but then he started thinking, ‘what about delay lines that didn’t and couldn’t exist in the real world?’ In walks, Valhalla Supermassive.
Now let’s get into what exactly this new plugin is all about. According to Valhalla’s website, Supermassive is based around feedback delay networks and designed to create reverbs and delays that sound massive. Feedback Delay Networks consist of a set of delays and a feedback matrix through which the delay outputs are coupled to the delay inputs.
Supermassive includes all of the features you’d expect in a standard delay but what really sets it apart from the pack is the Warp control. The Warp knob allows you to change the length of the delays in the network relative to the set delay time. The more you increase the warp value, the more delays in the network spread out. The results can range from simple echos, resonant delays, smeared reverb tails to massively lush reverbs. Another unique parameter in Supermassive is the density value. The density works by altering how the delays are mixed. 0% density means that the delays are completely parallel and not mixing at all. As you increase the density, the more the delays will be mixed together with 100%, meaning each network is completely mixed. 100% density usually yields a more familiar conventional sounding effect.
As with all Valhalla plugins, there is a built-in LFO that’s used for modulation, allowing users to create unique chorus and flanger sounding effects. The mix lock feature is nothing less than genius and something that should be built into all plugins; this feature allows you to set a mix percentage and lock it in so as you scroll through presets, it stays the same. If it were up to me, there would be a control lock feature for every plugin parameter.
On top of all of the previously stated features, eight different delay/reverb modes offer different characteristics and flavors.
There are so many unique new sounds and textures you can create with this one of a kind plugin… and it’s free! It’s a no brainer. Download this plugin right now! Supermassive is available for Mac or PC in VST/AU/AAX formats.